Search results for "Natural fiber"
showing 10 items of 52 documents
Mechanical properties of natural fiber composites produced using dynamic sheet former
2018
Composites formed from wood fibers and man-made cellulosic fibers in PLA (polylactic acid) matrix, manufactured using sheet forming technique and hot pressing, are studied. The composites have very low density (due to high porosity) and rather good elastic modulus and tensile strength. As expected, these properties for the four types of wood fiber composites studied here improve with increasing weight fraction of fibers, even if porosity is also increasing. On the contrary, for man-made cellulosic fiber composites with circular fiber cross-section, the increasing fiber weight fraction (accompanied by increasing void content) has detrimental effect on stiffness and strength. The differences …
Natural Compounds as Sustainable Additives for Biopolymers
2020
In the last few decades, the interest towards natural compounds, coming from a natural source and biodegradable, for biopolymers is always increasing because of a public request for the formulation of safe, eco-friendly, and sustainable materials. The main classes of natural compounds for biopolymers are: (i) naturally occurring fillers (nFil), such as nano-/micro- sized layered alumino-silicate: halloysite, bentonite, montmorillonite, hydroxyapatite, calcium carbonate, etc.; (ii) naturally occurring fibers (nFib), such as wood and vegetable fibers; (iii) naturally occurring antioxidant molecules (nAO), such as phenols, polyphenols, vitamins, and carotenoids. However, in this short review, …
Effect of Sheep Wool Fibers on Thermal Insulation and Mechanical Properties of Cement-Based Composites
2019
The use of sheep wool as a filler of cement in order to produce mortar or plaster involves several advantages for environment and energy. Moreover, it is considered as a waste and, therefore, its use is characterized by low cost. The aim of this paper is to evaluate the influence of wool fibers on thermal conductivity and mechanical properties of cement. The samples were prepared using wool fibers, obtained from a breed of Sicilian sheep, with three different lengths (i.e., 1, 6, and 20 mm). Furthermore, in order to evaluate the influence of fiber content, the samples were prepared by varying the fiber weight fraction. The thermal conductivity of the samples was analyzed by using a heat flo…
Assessment of Arundo donax Fibers for Oil Spill Recovery Applications
2019
In the last years, natural fibers are increasingly investigated as an oil recovery system in order to overcome the oil spillage phenomena, thus preserving environment and aquatic life. In particular, lignocellulose-based fibers have recently been employed with promising results. In such a context, the aim of this paper is to assess the oil sorption capability of natural fibers extracted from the stem of the giant reed Arundo donax L., a perennial rhizomatous grass belonging to the Poaceae family that grows naturally all around the world thanks to its ability to tolerate different climatic conditions. Sorption tests in several pollutants and water as a reference were carried out. The fibers …
On the response of flax fiber reinforced composites under salt-fog/dry conditions: Reversible and irreversible performances degradation
2022
Abstract Despite their scarce resistance to humid or wet conditions, natural fiber reinforced composites (NFRCs) seem to be able to partially recover their performances under discontinuous exposition to marine environment. To investigate this peculiarity, flax fiber reinforced composite was at first subjected to salt-fog spray condition at 35 °C for 15 and 30 days, respectively, and then stored in ‘‘dry” condition (i.e., 50% R.H. and 22 °C) between 0 and 21 days. The performances evolution was evaluated through flexural tests, water uptake and contact angle measurements. Moreover, the morphology of fractured mechanical samples was examined by using 3D optical microscope and scanning electro…
Characterization of a new natural fiber from Arundo donax L. as potential reinforcement of polymer composites.
2013
Abstract The aim of this paper is to study the possibility of using of Arundo donax L. fibers as reinforcement in polymer composites. The fibers are extracted from the outer part of the stem of the plant, which widely grows in Mediterranean area and is diffused all around the world. To use these lignocellulosic fibers as reinforcement in polymer composites, it is necessary to investigate their microstructure, chemical composition and mechanical properties. Therefore, the morphology of A. donax L. fibers was investigated through electron microscopy, the thermal behavior through thermogravimetric analysis and the real density through a helium pycnometer. The chemical composition of the natura…
Processing and mechanical properties of organic filer-polypropylene composites
2005
The addition of organic fillers into thermoplastic polymers is an interesting issue, which has had growing consideration and experimentation during the last years. It can give rise to several advantages. First, the cost of these fillers is usually very low. Also, the organic fillers are biodegradable (thus contributing to an improved environmental impact), and finally, some mechanical and thermomechanical properties can be enhanced. In this study, the effect of the addition of different organic fillers on the mechanical properties and processability of an extrusion-grade polypropylene were investigated. The organic fillers came from natural sources (wood, kenaf, and sago) and were compared …
Drilling characteristics and properties analysis of fiber reinforced polymer composites: A comprehensive review
2023
Fiber-reinforced polymer (FRP) composites play a vital role in the production of structural and semi-structural components for engineering applications. The drilling process is a commonly employed machining process for FRP composites to join the FRP structural elements. Usually, the FRP composites possess a heterogeneous nature because of their multi-layered structure, hybridization, and the presence of multi-phase materials. Hence, common problems like delaminations, fuzzing, buckling, cracking, matrix and fiber burning occur during the drilling operations. These problems cause dimensional inaccuracy, poor surface finish, and tool wear and reduce the mechanical strength of the composites. …
The effect of mechanical defects on the strength distribution of elementary flax fibres
2009
Flax fibres are finding non-traditional applications as reinforcement of composite materials. The mechanical properties of fibres are affected by the natural variability in plant as well as the damage accumulated during processing, and thus have considerable variability that necessitates statistical treatment of fibre characteristics. The strength distribution of elementary flax fibres has been determined at several fibre lengths by standard tensile tests, and the amount of kink bands in the fibres evaluated by optical microscopy. Strength distribution function, based on the assumption that the presence of kink bands limits fibre strength, is derived and found to provide reasonable agreemen…
Modeling strength scatter of elementary flax fibers: The effect of mechanical damage and geometrical characteristics
2011
Elementary bast fibers, apart from acceptable specific mechanical properties, possess a marked variability in geometrical and damage characteristics, which affects their axial tensile strength. A strength distribution function is derived that allows for the effect of kink bands and the scatter of fiber diameter. The distribution function is validated by applying it to the experimental strength data of both intact, carefully hand-decorticated, and damaged elementary flax fibers obtained by standard processing. The results suggest that the presence of kink bands is a limiting factor for the fiber strength.